Search among more than 1.000.000 user manuals and. VistaLINK® PRO SNMP. Monitoring & Control for all Applications VistaLINK® PRO: VistaLINK PRO is Evertz. Used in accordance with the instruction manual. VistaLINK™ PRO and 7742DLY-HD Feb 04. With Evertz’s VistaLINK™ PRO server running on the same network. • 7800 MultiFrame Manual 7800FC VistaLINK® Frame Controller TABLE OF CONTENTS OVERVIEW...1 INSTALLATION....2 2.1. INSTALLING THE MODULE REAR PLATE.. INSTALLING AND REMOVING THE MODULE..4 2.3. REAR PANEL CONNECTIONS... Ethernet Connection...5 2.3.2. • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® 6.2.1. Network Setup...15 6.2.2. SNMP Setup...17 6.2.2.1. SNMP V1 Setup..17 6.2.2.2. Community Strings..17 6.2.2.3. Trap Setup...18 6.2.2.4. SNMP V3 Setup..18 6.2.3. • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® Figures Figure 1-1: 7800FC Block Diagram...1 Figure 2-1: 7800FR Rear Panel with Cover Plate Installed..2 Figure 2-2: 7800FR Rear Panel Kit Installation... 3 Figure 2-3: 7800FC Rear Panel...5 Figure 2-4: Crossover Cable Wiring Diagram.. • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® This page left intentionally blank Revision 1.0. • Feb 2014 Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® This page left intentionally blank Revision 1.0. • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® OVERVIEW The 7800FC VistaLINK® Frame Controller card provides a single point of access to communicate with VistaLINK -capable modules. The 7800FC VistaLINK Frame Controller provides a 10BASE-T/100BASE- ® ® TX/1000BASE-TX Ethernet port and communication is facilitated using Simple Network Management Protocol (SNMP). • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® INSTALLATION The 7800FC Frame Controller module can only be installed into 7700FR-C, 7800FR and 7800FR-QT frames that have been fitted with the proper module interconnect circuit board. These frames have an ‘L’. • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® Figure 2-2: 7800FR Rear Panel Kit Installation Page-3 Revision 1.0. • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® 2.2. INSTALLING AND REMOVING THE MODULE In order to insert or remove modules you will have to open the front panel. Turn the two captive screws located on the front panel counter clockwise several turns until they release completely from the front extrusions. • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® 2.3. REAR PANEL CONNECTIONS Figure 2-3: 7800FC Rear Panel 2.3.1. Ethernet Connection The 7800FC is designed to be used with either 10Base-T (10 Mbps), 100Base-TX (100 Mbps) also known as Fast Ethernet, or 1000Base-TX (1000 MBps) twisted pair Ethernet cabling systems. When connecting for 10Base-T systems, category 3, 4, or 5 UTP cable as well as EIA/TIA –. ![]() ![]() • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® The straight-through RJ-45 cable can be purchased or can be constructed using the pinout information in Table 2-1. A colour code wiring table is provided in Table 2-1 for the current RJ-45 standards (AT&T 258A or EIA/TIA 258B colour coding shown). • 7800 MultiFrame Manual 7800FC VistaLINK Frame Controller ® If you are building a “crossover” cable you must wire it according to Figure 2-4: Figure 2-4: Crossover Cable Wiring Diagram 2.3.2.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
March 2019
Categories |